Standard Size Clear Float Glass for Building

FLAT TEMPERED GLASS AND HEAT-STRENGTHENED GLASS

Equipment
1.TAMGLASS flat tempering furnaces from finland.
2. Compelled convection tempering machine with heated airflow

Procedures:
Tempered glass is made by heating flat glass to just below its softing temperature and suddenly cooling it with jets of cold air. lt results the outer skins under powerful compressive stress and the interior with severe tensile stress.the difference between tempered glass and the heat-strengthened 
glass is the different parameter in the heating and cooling process.
Performance:
Tempered glass is excellently safer glass and the fragment of which does no big harm to humans. It is 4-5 times harder than ordinary annealed glass.Heat-strengthened glass has a strength that is 2-3 times than the ordinary anneal glass. with a relatively low proportion of spontanecus brakeage,heat-sterngthened
glass retain in the frame after breakage because of the blocks that radiate to the edge of the glass. which make the replacement of the glass more convenient
Application Scopes:
Sites with the facilities have the demand of strength and protection, such as glass wall, door, window, show window, bar-protetor folding screen
Our Characteristics:
Imported equipment of high quality and high value can meke the surface of the tempered glass meet the needs of the strict requirement for
architecture,fumiture,electron industy compelled convection tempering machine makes the tempered glass without stripe of the stress,so that the 
sheets assembled on thecurtain wall will be more transparent and beautiful. The temperable thicknesses of the glass range from 3mm to 25mm.

CURVED TEMPERED GLASS
Machines:
Curved Tempered Furnaces
Manufacture techniques:
The glass is heated over its softening temperature, and curved to the radius that requires. By suddenly chilling it with jets of cold air, then shape into curved 
tempered glass with radian required.
Performance:
The curved tempered glass has the same safety and ability of anti-impact as flat tempered glass, while has a better wind pressure strength and deflection
 than flat tempered glass.
Scope of Applications:
Glass assembled on the sites with the requirement for the appearance, safety and strength.
Our characteristics:
The excellent photic performance of the surface of the curved tempered glass is prefectly fit for the curved laminated glass. 3500mm in width of the furnace 
provide the possibility to process the big-sized curved tempered glass and good in quality. The small radius of 420mm makes up the deficiency of the big radius
tempering machine.

HEAT SOAK TREATMENT
Equipment:
Computerized heated air circulation heat soak furnace
Procedures:
Keep the tempered glass in the funace for 2-8 hours at the temperature of 290ºC±10ºC, then take out after cooling
Application Scopes:
In order to reduce spontaneous breakage of tempered glass, heat soak test is needed by tempered glass that is used in the field of architecture, sanitary,
 furniture, electron.
Our Characteristics:
Use a thermometer to control the temperature of the glass surface to ensure the standard envrionment of the heat soak test that is going under 290ºC±10ºC.
Glass with Nis will be break in the furnace at most and the proportion of spontaneous breakage will be highly reduced.
Spontaneous breakage of tempered glass and Solution:
The spontaneous breakage of tempered glass is caused by the existance of Nis in the raw material.Nis can not be eliminated completely because it is a resultant of the reaction When producing the raw material.When glass is heated for tempering Nis will tranaform from β state to α state,but when glass is then quenchod, 
Nis will not be ablo to return to the original β state.  With the passing of time and corresponding change of the environment, α-Nis will return to β -Nis and its volume will expand for 2-4%. The expansions of Nis volume will possibly tigger the glass to break eventually. Spontaneous breakage of tempered glass 
will bring much trouble, especially when it is installed to use. The practical solutions many technicians follow are:
1. Heat soak teat is a selective process which allows tempered glass to break in the heat soak furnace, and the percentage of spontaneous breakage will be greatly reduced.
2. Use the heat strengthed glass instead of the tempered glass to make the replacing process easy.
3. Prepare more spare parts in order to replace the broken panel in time because of the relatively low percentage of  spontaneous breakage. Although
 heat soak test can not eliminate the spontaneous breakage of the tempered glass, it will greatly reduce the chance of tempered glass breaking. The stress
of the glass will slighty drop after the heat soak test. Because there is no specfic way to identity whether the glass has already been heat soaked, it is advised to 
select glass manufactures with well reputation to conduct the test.

FLAT/CURVED LAMINATED GLASS
Equipment:
Two production lines for flat and curved laminating glass
Procedures:
Two or more sheets of glass bonded together with one or more interlayers(PVB). And then converge with high temperature and high pressure.
Performance:
Laminated glass is a kind of safe glass because of the fragment will stick to each other after being impinged. Besides, it can effectively prevent the hard object from
penetrationg through the glass , greatly reducing the harm done to humans.Three or more sheets with two or more pieces of PVB will be used as theftproof and 
bulletproof glass.Laminated glass can block the ultraviolet radiation effectively by 99%, so that objects inside the room can be prevented from aging caused by the sunshine. People can enjoy the sunlight without worrying about being burnt by the ultraviolet radiation.Laminated glass can reduce the spread of sound.
Application Scopes:
Sites with a requirement of protection and anti-ultraviolet radiation, such as glass curtain wall, door and window. sunshade.elevator for sightseeing, aquarium,etc.
Our characteristics
Selection of PVB with good quality and equipment for dehumidification prevent the PVB from deteriorating, aging and discolouring. With more than one autoclava tunnel, big output makes the rapid replacing of products' category and delivervy in-time.
 

FLAT/CURVED INSULATED GLASS

Equipment:
Austria LISEC insulating production line with the aluminum automatic bending machine and desiccant filling machine.
Procedures:
Insulating glass is a multi-glass combination consisting of two or more panels enclosing a hermetically-sealed air space. The  sheets are connected by an aluminium spacer with the desiccant inside, and the whole unit is hermetically assembled by 
double sealant (butyl, ply-solitude, silicon, etc.). The function will be enhanced if the function of insulated glass will be 
enhanced if inert gas was filled.
Performance:
Heat insulation. Low coefficient of heat conductivity can prevent the effective exchange will be of the heat.The energy 
consumption (air conditioner, central heating ,etc.) will be cut down accordingly.
Sound insulation. The noise can be cut down by 30~45 db. With insulated glass assembled on the doors and windows, 
a quiet and comfortable environment for work and rest will still be kept even if you are in the downtown area with 
busy traffic.
Anti-condensation. Insulated glass keeps good perspective property without dew or fog even at the temperature below-45ºC.
Insulated glass can be made with the compounding of several functional sheets to enhace capability, such as tempered 
insulated  glass,  laminated insulated glass, curved insulated glass, Low-E insulated glass,insulated glass with coating 
and TEC electric coating insulated glass, etc.
Application Scopes:
The curtain wall, door, window, icebox with
Our characteristics:
We have advanced equipment, large quantity of output, complete category. Raw material with high quality assure the 
quality of our products.
Insulated glass products manufactured by the aluminum bending machine makes the quality better.

 

YONG MING GROUP have been producing Architectural Glass, Aluminum Windows and Doors and Curtain Walls since 1997 in our factories, 
located in South China, only 70mins. by Ferry from Hong Kong.  Located in Dongguan city of Guangdong Province, one famous international manufacturing city in South China, our factories are the transportation hub of Guangzhou, Shenzhen and Hong Kong.

Strengths
All the factories covers an area around 100, 000 square meters, owning 50, 000 square meters of modern industrial plants, and have a strong R & D technical management team and produ- ction team, a large number of production equipments from famous European manufacturers, and our manufacturing technologies keep the level with the world.
Equipments
Our factories own Italian computerized cutting production lines for glass and aluminium,impor- ted edge grinding production line, Finland Tamglass tempered furnace,LAND Curved tempered furnace,Swiss Bystronic hollow Low-E coated glass production machines, Austria LISEC Insu- alted glass production machines,laminating production lines,Heat Soak furnaces, ceramics pri- nters, Self-cleaning production line.

We passed the certification ISO9001 by the England Intertek Institution, and obtained the com- pulsory 3C quality certification of Chinese tempered and laminated glass products. At the same time, we passed many certifications such as European Union EN, Australia AS/NZS, USA IGCC/SGCC, Japan JIS and so on.

 

Follow with the step of continuously improving the quality actively develop new products for the internationalization

Q1:Are you a Trading Company or a Manufacturer?

A:We are a real manufacturer.

Q2: Do you accept customized design and size?
A:Of course.We accept all kinds of customized styles.

Q3:What is your main product?
A:casement door/sliding door/folding door/casement window/sliding window/awning window/sun room.

Q4: How long is your delivery time?
A: Generally it is 15~20workdays it is according to your quantity.

Q5: What is your terms of Standard payment ?
A: T/T in advance ,balance before shippment.